C-Tec
Know what you're looking for?
Showing 51–100 of 133 results
-
C-Tec CFP AlarmSense 2, 4 or 8 Zone Panel
C-Tec- Apollo AlarmSense panel
- Available 2, 4 or 8 zones
- Wide range of engineering functions including zone test, coincidence, zone delay and non-latching zones
- Third-party LPCB tested
-
-
C-TEC CFP Relay Output Card – 12 Relays
C-Tec- Provides Reset, Fault, Aux Fire and Remote Relays
- 8 Outputs per Zone Relays
-
-
-
-
C-Tec FF502P 4 Zone Sounder Circuit Extender Kit
C-Tec- Provides four extra conventional sounder circuits with open and short circuit fault monitoring.
- Compatible with most manufacturers' fire alarm control panels.
- Supplied on a double gang plate.
-
C-Tec Hi-Output XP95 Wall Sounder
C-TecKey Features
- Third-party certified to EN54-3 (Sounders) and 17 (Isolators) by the LPCB
- Impressive 103dB(A) sound output @ 1m
- Onboard short-circuit loop isolator
- 550µA quiescent current./li>
- 5mA alarm current @24V DC (sounder on max)
- Group addressing facility allows multiple devices to be operated simultaneously
- 7 selectable volume levels and up to 15 selectable tone pairs
- IP21C (Type A) rated.
- Third-party certified to EN54-3 (Sounders) and 17 (Isolators) by the LPCB
-
C-Tec Lid for Base Sounder in White or Red
C-Tec- Optional lid for C-Tec base sounders.
- Available in white or red.
-
C-Tec NC302RXC Master Infrared Ceiling Receiver
C-Tec- Receives line-of-sight infrared signals from up to 10 meters away, depending on environmental conditions
- Includes a red LED that confirms when a call has been made
- Requires a separate remote reset point, such as a button or keyswitch, to cancel calls
-
C-Tec NC802DB Standard Call Point, Button Reset with Remote Socket
C-Tec- The call point features a button reset mechanism
- It includes a 6.35mm jack plug socket for remote operation
- The design is suitable for use in 800 Series Call Systems
-
C-Tec NC802DEB-1/2 Emergency Call Point, Button Reset with Remote Socket
C-Tec- Includes a 6.35mm jack plug socket for connecting optional devices like a tail call lead or pressure mat
- Features a red reassurance LED that confirms when a call has been made
- Provides an onboard reset button to cancel standard and emergency calls made from the NC802DEB-1/2, as well as standard calls from other devices on the same zone
-
C-Tec NC802DEWA IP67 Emergency Sauna/Steam/Wet Room Alarm Point, Requires NC889ERM
C-Tec- It has a surface-mounted design with a 35mm black back box, yellow call point, and white push button
- It comes supplied with a set of branding stickers
- The IP67 rating ensures it is protected against water ingress and can withstand the harsh conditions found in saunas and steam rooms
-
C-Tec NC802DEWP IP67 Emergency Pool Alarm Point, Requires NC889ERM
C-Tec- IP67 rated panic alarm point for swimming pools
- Compatible with 800 Series Call System via NC889ERM
- Includes a black back box, blue call point, and white push button
-
C-Tec NC804DE Emergency Only Call Point, Button Reset
C-Tec- The onboard reset button can cancel emergency calls made from the NC804DE and standard calls made from other devices on the same zone
- It is ideal for use as a reset point for ceiling pull units, allowing a more urgent emergency call to be made if additional assistance is required
- A red reassurance LED confirms when a call has been made
-
C-Tec NC805AS Air Switch for NC805P
C-Tec- Operates at a minimum differential air pressure of 0.9 p.s.i (6220 Pa) ± 10% at 16°C
- Ideal for use by patients or residents who need to activate a nurse call system
- Connects to the NC805P pneumatic pad via a 6.35mm jack plug
-
C-Tec NC805C/14 4.2m (14ft) Tail Call Lead
C-Tec- Allows users to remotely generate standard calls from various locations
- Features a pear-shaped call push, 4.2m (14ft) trailing lead, and a 6.35mm remote jack plug
- Easily connects to the 6.35mm remote socket on compatible Quantec and 800 Series call points
-
C-Tec NC805C/6 1.8m (6ft) Tail Call Lead
C-Tec- The lead comprises a pear-shaped call push, a 1.8m (6ft) trailing lead, and a 6.35mm remote jack plug for easy connection to compatible call points
- Activating the pear push or removing the tail call lead from a call point's remote socket will generate a standard call, providing users with greater flexibility and accessibility
- The 6.35mm remote socket on compatible Quantec and 800 Series call points allows for seamless integration and easy installation of the tail call lead
-
C-Tec NC805D 1.2-3.6m (4-12ft) Coiled Tail Call Lead
C-Tec- Allows users to remotely generate standard calls from armchairs, beds, and other locations
- Comprises a pear-shaped call push, coiled 1.2-3.6m trailing lead, and a 6.5mm remote jack plug
- Easily connects to the 6.35mm remote socket on compatible Quantec and 800 Series call points
-
C-Tec NC805MD Portable Movement Detector
C-Tec- Portable, robust, and easy to adjust for use in residential care facilities
- Ideal for patients who have difficulty adjusting or suffer from dementia, as it requires no components in the bed itself
- Easily connects to compatible Quantec and 800 Series call points through the 6.35mm remote socket
-
C-Tec NC805P Hand/Foot Operated Pneumatic Pad
C-Tec- The pneumatic pad operates the highly-sensitive NC805AS air switch, which is sold separately
- The NC805AS air switch, when connected to a compatible call point's remote socket via its 6.35mm remote jack, triggers a standard call
- The C-Tec NC805P is ideal for people who have difficulty pressing buttons on standard call leads
-
C-Tec NC806C Overdoor Light
C-Tec- Offers visual alerts with a constant red light for standard calls and a pulsing red light for emergency calls, ensuring clear communication of the call type
- Features dual red LEDs and a triangular diffuser for high visibility from a distance, enhancing safety and response times
- Constructed from durable ABS plastic and compatible with standard UK 25mm single gang flush or surface back boxes, making it versatile for installation in different environments
-
C-Tec NC806C Overdoor Light with Sounder
C-Tec- Visual indication of 800 Series Alarm calls with red lights for Standard and Emergency calls
- Highly visible design with dual red LEDs and a triangular diffuser
- Versatile mounting options on standard UK back boxes
-
C-Tec NC807C Ceiling Pull Unit
C-Tec- Can be used to generate a standard call on an 800 Series Conventional Call System.
- Typically wired as a slave to an 800 Series Call Point or Reset Point so that its calls can be cancelled.
- Supplied with 3m of red nylon pull cord and two red open-sided triangular bangles for ease of use by the infirm.
- Red confidence LED and diffuser emits a bright red glow over a wide area to reassure the user that a call has been made.
- Surface mountable.
- Base fits 16mm conduit and BESA centres.
-
C-Tec NC809DB Button Reset Point
C-Tec- It mounts on a standard UK 25mm single gang flush or surface back box
- It can be used to remotely cancel standard calls generated from ceiling pulls and/or wall call points that are wired on the same zone
- It is designed for use with C-TEC's 800 Series Call System
-
C-Tec NC809DB/SS Button Reset Point in Stainless Steel
C-Tec- Compact 87 x 87 x 24 mm design that mounts on a standard UK single gang back box
- Provides audible and visual indication when a call is acknowledged to reassure users
- Can be used as part of an accessible toilet alarm system to cancel calls from inside the WC
-
C-Tec NC809DBBT Accessible Toilet Reset Point with Sounder
C-Tec- Allows calls from the NC807C ceiling pull unit to be cancelled from inside the toilet
- Provides visual and audible indication to the user that their call has been acknowledged and help is on the way
- Can be mounted on a standard UK single gang back box and is also available as part of the NC951 accessible toilet alarm kit
-
C-Tec NC809DM Magnetic Reset Point
C-Tec- The NC809DM can be used to remotely cancel standard calls from the 800 Series Call System
- It requires a separately available NC803M magnetic reset key to operate the magnetic reset target
- The device mounts on a standard UK 25mm single gang flush or surface back box
-
C-Tec NC883D 12V Relay Unit
C-Tec- Can be directly triggered from the call system's signal lines, provided the unit is supplied with +12V and -V power
- Typically used to switch extra low voltages, but can also switch mains voltages when following the guidelines in the instructions
- Incorporates a high-intensity LED that illuminates red when the relay is active, and includes a white "write-on" area for personalizing the unit
-
C-Tec NC888D Remote Sounder
C-Tec- Connects to multi-zone 800 Series Call Controllers, Master Indicator Panels, or Switchable Sounders
- Indicates Standard calls with a constant tone and Emergency calls with a pulsing tone
- Limit of two remote sounders per hosting device
-
C-Tec NC889 Call Latch Module
C-Tec- Measures just 30 x 20 x 15mm, making it ideal for discreet installation inside or alongside the monitored device
- Includes a red reassurance LED that illuminates when a call is made
- Provides multiple wiring options via the device's colored leads, allowing it to be easily integrated with a variety of switch assemblies
-
C-Tec NC889ERM Multi-Purpose Call Latch Module
C-Tec- Includes a red reassurance LED that illuminates when a call is made
- Provides an onboard magnetic reset facility for cancelling calls
- Offers multiple wiring options via the device's colored leads, making it ideal for applying 800 Series call point electronics to custom-made switch assemblies
-
C-Tec NC894DKB Isolatable Monitoring Point, Button Reset
C-Tec- It can be used to monitor any device with a normally open or normally closed switch
- It has an isolation keyswitch that temporarily turns off the device's monitoring function when in the isolated position
- It triggers a standard call when activated, making it suitable for monitoring fire exits, drug cupboards, store rooms, and other similar applications
-
C-Tec NC899IRR Keyswitch Reset Point
C-Tec- Momentarily turning the keyswitch to the "ISOLATE" position resets the call
- The keyswitch must be returned to the "ON" position after reset, as leaving it in "ISOLATE" will disable the NC302RXC receiver's emergency call function
- The reset point mounts on a standard UK 25mm single gang flush or surface back box
-
C-Tec NC917L Standard Call Push with Protruding Button, No Reset, No Remote
C-Tec- The red LED confirms when a call has been made
- It requires a separate reset point to cancel calls
- It mounts on a standard UK 25mm single gang flush or surface back boxvvvvvvvvv
-
C-Tec NC951 Disabled Persons Toilet Alarm Kit
C-Tec- The UK's market-leading Disabled Persons Toilet Alarm kit.
- Includes everything required for a BS8300 clause compliant emergency assistance alarm.
- Attractively designed, easy to install and simple to use.
-
C-Tec NCP Double Gang Surface Interface Plate
C-Tec- Adapts to most European fixing centers for flexible installation
- Available in multiple variants, including single gang shallow, single gang deep, double gang shallow, and double gang deep options
- Designed to match C-TEC's existing plastics and colors for a cohesive aesthetic, and can also be surface mounted directly to a wall
-
C-Tec NCP Single Gang Surface Interface Plate
C-Tec- Adapts to most European fixing centers for flexible installation
- Available in multiple variants, including shallow and deep options, to suit different application needs
- Designed to match C-TEC's existing plastics and colors for a cohesive aesthetic
-
C-Tec NCP-13 Anti-Bacterial Wipe Clean Pull Cord Accessory Pack
C-Tec- The cord has integral properties that can help prevent the spread of infections such as MRSA, E.coli, C.diff, and Norovirus
- The pack is easy to clean using a cloth and mild detergent
- It is compatible with a wide range of ceiling pull units from various manufacturers
-
C-Tec NCP-27 Adaptable Conduit Box
C-Tec- Product dimensions (mm): 101 x 38mm (3mm thick). Internal wiring depth: 33mm
- Construction & finish: White PVC. RAL9003 Blue White.
- Weight: 86g
- Notes: Supplied with 2 x K40 x 30mm fixing screws; Flammability rating: UL 94-5VA; Relevant standard: BSEN 60670-1
-
-
-
C-Tec QT412RXA Rechargeable IR/RF Transmitter, Push/Pull For Attack
C-Tec- Enables staff to remotely signal attack/emergency situations on compatible infrared call points, ceiling receivers, or radio receivers
- Can also be used to trigger standard and emergency calls on 800 Series call systems
- Includes a karabiner clip for attaching to staff uniforms and can be recharged using a single or ten-way charging unit
-
C-Tec QT412RXCA Rechargeable IR/RF Transmitter, Push For Call, Pull For Attack
C-Tec- Transmits calls up to 10 meters away via infrared or radio signals, depending on the receiving device
- Includes a karabiner clip for attaching to staff uniforms, and can be programmed to generate different call levels
- Can be recharged using a single-way or ten-way charging unit, and transmitters on Quantec systems can be programmed with a unique user ID
-
C-Tec QT424/1 Single Way Charger for QT412 Range Transmitters
C-Tec- Connects to a standard 13A mains socket
- Provides a typical 14-hour charging time for a full cycle
- A 10-way version (QT424/10) is also available for charging multiple transmitters
-
C-Tec QT424/10 Ten Way Charger for QT412 Range Transmitters
C-Tec- Can be wall or desk mounted to suit the transmitter storage and charging requirements
- Fully recharged transmitters can be left connected to the charger with no detrimental effect
- Indicators confirm when charging is complete
-
C-Tec QT616 Quantec Infrared/Radio Fall Sensor
C-Tec- Transmits up to 10m line-of-sight and has RF coverage dependent on the Quantec receiving device used
- Includes a Karabiner clip and lanyard for easy attachment
- Can be programmed to generate different call levels and include a unique user ID/name
-
C-Tec QT644 Floor Pressure Mat
C-Tec- The mat triggers a standard call on a Quantec or 800 Series Call System when foot pressure is detected
- It has a tough, durable grey PVC finish with a non-slip rubber base
- The mat connects easily to the 6.35mm remote socket on compatible Quantec and 800 Series call points
-
C-Tec Quantec Network Splitter
C-Tec- An essential wiring/installation aid for C-TEC's Quantec Addressable Call System
- Helps protect against open and short circuit faults and reduces the risk of volt drop
- Includes one input and one output connection for Quantec's 'Spine' wiring (typically 1.5-2.5mm T&E) and six fused 400mA ‘limb’ connections for the wiring of individual circuits containing Quantec's field devices (typically 4 core stranded security cable)
- At least one QT603 is required per Quantec system (the more you use, the easier it will be to program and fault-find)
- Install one QT603 per corridor junction (locate at the end of the corridor nearest to the Quantec Controller). If the corridor is longer than 50m, install the splitter in the centre of the corridor to reduce wiring runs
- Mounts on a standard 25mm UK double gang back box
- 'Power' and 'Fault' indicators
- Max. 60 addressable devices per QT603.
-
C-Tec Relay on a Plate 24v 5A (single gang)
C-Tec- A general purpose, double-pole, polarised 24V 5A relay designed for use in 24V fire alarm systems.
- Incorporates a high intensity LED which illuminates red when the relay is active.
- Can be connected to a suitable control panel relay output or a standard polarised fire alarm sounder circuit to operate door retaining magnets, rollershutter doors, etc.
- Can be mounted on 25mm flush or surface mount back boxes.